• CAPS/BANGERS NOT INCLUDED**
• by Glob Mob
• 6'' and 3'' long
• available in triple on single slots
• 3d printed

A MESSAGE FROM GLOB MOB

NEW DESIGN FITS UP TO 3 CAPS 23mm OR GREATER!!! The silicone ring at the top flawlessly supports most carb caps! The holder also has a silicone drip pad to help make the cleaning process a little easier. Any carb cap greater than 23mm will fit!

DIMENSIONS / SIZE
– The base is about 7.25″/184mm in width
– The height of holder is about 1″ /27mm
– The inside of diameter of the silicone ring is 23mm
– The base is about 70mm/2.75″ in depth
– ANY CARB CAP GREATER THAN 23mm WILL FIT!!!

*PRODUCT DISCLAIMER*
-Carp caps are not included in purchase
To maintain best the best quality for the longest time make sure to:
– Keep products out of direct sunlight
– Try and avoid storing in temperatures above 85 Degrees
– Do not pull on silicon pieces
-Use a clean paper towel with isopropyl alcohol to clean product when dirty.

CLEANING INSTRUCTIONS
– The Silicone Carb Cap Holder is safe to clean with rubbing alcohol, but don’t soak it for extended periods of time or it will affect the color.

• CAPS/DABBERS NOT INCLUDED***
• By Glob Mob
• 3d printed
• 3 carb cap slots
• 2 place holders for dabbers
• made in the usa
• 6'' long

        A MESSAGE FROM GLOB MOB

Introducing the Triple-Double Mini Combo Station. This combo station will hold up to two dabbers and three carb caps. The carb cap holders are lined with a silicone ring to protect against heat and sticking! There is also a silicone drip pad at the bottom of the holder to make clean up easy! Any carb cap greater than 23mm will fit.

The combo station also comes equipped with two holders for glass or plastic dabbers. The distance between the two posts is about 1.3″ (40mm exactly)

If you have any concerns about your cap or dabber fitting, just send us a message!

Over 2 and a half years of experience with 3D printing have allowed me to dial in the settings on my printer to an absolutely perfect level. No visual flaws or defects here. The professional quality of our prints is bound to impress you and open your mind to the world of 3D printing.

While bringing new innovations to the world is a passion of ours, so is helping the environment. This carb cap stand is manufactured using a corn-based bio-plastic known as PLA (Poly Lactic Acid). PLA is not only a renewable resource, but its also “100% BIODEGRADABLE” which is something that almost no other plastics out there can say. So by buying our products, you can call yourself a proud supporter of a green company.

Carb Caps and Dabbers are not included!!!

*PRODUCT DISCLAIMER*
To maintain best the best quality for the longest time make sure to:
– Keep products out of direct sunlight
– Try and avoid storing in temperatures above 85 Degrees
– Do not pull on silicon pieces
-Use a clean paper towel with isopropyl alcohol to clean product when dirty.

CLEANING INSTRUCTIONS
– The Silicone Carb Cap Holder is safe to clean with rubbing alcohol, but don’t soak it for extended periods of time or it will affect the color.



• SWABS NOT INCLUDED**
  
• by Glob Mob 
• oil drum design
• storage for swabs
• 3d printed
• 3'' tall

Tired of loose q-tips cluttering your space? Keep your dab station clean and organized with the Oil-Drum Q-Tip Holder by Glob Mob! The size of the cavity was purposely designed to fit all q-tips in an organized manner! Check out all the different colors to match the rest of your setup! The Qtip Holder is just one component of the Glob Mob starter kit, check out our Single Dabber Stand, and Silicone Carb Cap Stand for the rest!

*PRODUCT DISCLAIMER*
To maintain best the best quality for the longest time, make sure to:
– Keep products out of direct sunlight
-Use a clean paper towel with isopropyl alcohol to clean the product when dirty.